Brembo PS 13 handlebar mounted clutch master cylinder, supplied complete with lever.

 This part is available by special order, request a quote

Pair of triangular side panels with fixings to fit all Tonti frame models with slotted side panel lugs under the seat

This is a kit, the fixings need bending and glueing to the sidepanel before the side panels can be fitted. The panels are GRP, fitting instructions are provided in German

 This part is available by special order, request a quote

Short screw in polished alloy thermometer dipstick with O ring for models without a sump extension. Shows oil temperature in degrees celcius

Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick

 This part is available by special order, request a quote

17004951-z 17004951 GU17004951 17 00 49 51
 1700 4951 1700.4951 17.00.49.51

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Complete single disc clutch kit for 5 speed big twins containing flywheel, new deep spline clutch hub, friction plate, spring plate, pressure plate, and flywheel bolts. Suitable for all big twins with either distributor or crankshaft mounted ignition system, not suitable for Digiplex equipped models.

This clutch upgrade has the following advanges over the old two plate clutch:

• Reduction in flywheel and clutch weight of approx. 1KG
• Improved acceleration
• Smoother gear changes at high RPM
• Quicker engine decelleration
• Reduction in engine vibration as the clutch assembly is (this is not possible with the original clutch)
• Lighter handlebar clutch lever action
• More precise clutch engagement and disengagement.
• More progressive clutch engagement.
• Increased ability to handle higher torque and horsepower.
• Lower clutch disk wear (reduced maintenance)
• Fewer parts (no intermediate plate, no second friction plate) to wear out
• Ease of assembly - gearbox can be fitted to engine without centering of the clutch disk.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Gorgeous polished aluminium reservoir cap for PS15 Brembo master cylinder fitted to rear linked system on many models, will fit front master cylinder on models where a PS15 handlebar master cylinder is fitted. Seal is not included with this cap - you should re-use your original cap seal

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR

Black painted steel footboard supplied with separate rubber. Fasteners included.

Please note that rubber is supplied unattached and ready for glueing.

 This part is available by special order, request a quote

 18443450 GU18443450 18 44 34 50
 1844 3450 1844.3450 18.44.34.50

Lightweight 5mm battery plate in a silver finish, supplied with countersunk M8 screws

This is an upgrade to the standard steel plate, perfect for your Tonti framed special (it will also fit Cali 1100 and Cali EV based specials. On some models you may need to enlarge the cut out for the speedo cable

 Availability varies on this part, check availability

14418200-z 14418200 GU14418200 14 41 82 00
 1441 8200 1441.8200 14.41.82.00

Set of highly polished aluminium round barrel rocker covers (Guzzi ref. 17023550 or 17023560). Ideal for finishing off your restoration project

This rocker cover set also known as Guzzi ref. 14023550, these can be fited to square barrel models if fitted with adapter kit ACA30310

 This part is available by special order, request a quote

 17023560 GU17023560 17 02 35 60
 1702 3560 1702.3560 17.02.35.60

Gorgeous polished aluminium reservoir cap for PS12 Brembo master cylinder fitted to front brake on many models, fits rear master cylinder on more recent models

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 10430830 GU10430830 10 43 08 30
 1043 0830 1043.0830 10.43.08.30